Audio Joiner & Merger
Combine multiple audio files in order. Add a gap or a crossfade between clips, then preview and export a WAV locally.
0 files, about 0 minutes before transitions. Files stay on your device.
Crossfades are shortened for clips shorter than twice the selected fade. Long exports may use substantial memory.
Audio joiner: combine files in the right order without uploading
Two 3-minute recordings joined back to back make about 6 minutes of audio. Add a 2-second gap and the result is about 6 minutes and 2 seconds. A 2-second crossfade makes it about 5 minutes and 58 seconds instead. Those small differences matter when you are assembling an audition reel, a podcast intro or a continuous practice track. Add your files above, put them in order and listen before you download.
Choose the order first
The joiner takes whole audio files in the order shown in the list. Drag a file or use Up and Down to move it. It does not trim introductions, detect silence or match musical tempo. If your first recording includes a count-in you do not want, remove it with the audio trimmer before joining. If you need silence removed automatically from the edges, try the silence trimmer. Listen to every cut in context, especially when source recordings have different levels.
Direct joins, gaps and crossfades
With both gap and crossfade set to zero, one file ends and the next begins immediately. A gap inserts silence between files. A crossfade overlaps the end of one file with the beginning of the next. The gap setting is ignored when you choose a crossfade. A short overlap can hide a hard edit between ambient recordings, but it can also blur spoken words or two drum hits. For spoken material, try a direct join first. For a continuous music bed, start with a one-second overlap and listen to the transition.
How overlap length is calculated
For each boundary, the requested overlap is capped at half the length of each neighboring clip. If you join a 1-second sound to a 3-minute recording with a 4-second crossfade, the usable overlap is at most half a second. This prevents one very short clip from disappearing inside the following one. The output duration is the sum of file durations, minus actual overlaps, or plus gaps when you do not crossfade. Millisecond rounding and resampling can change the final length by a few samples.
Linear and equal-power curves
Linear fades multiply the first recording by 1 minus the fade progress and the second by the progress. Halfway through, each plays at half amplitude. Equal-power fades use cosine for the outgoing side and sine for the incoming side. At the midpoint, each is about 0.707 of its original amplitude. That often prevents a perceived dip between unrelated recordings. With closely correlated recordings, equal-power overlap may instead make the center louder. The tool applies the same fade math as our two-track crossfade tool, but this page does not try to beat-match or analyze musical compatibility.
Sample rates, channels and export
The browser decodes each file and resamples it to the first file's sample rate when rendering. A mono source is sent to both channels in stereo output. Output has at most two channels. The result is a WAV file, so it may be larger than the MP3 files you added. For example, one minute of stereo 44.1 kHz 16-bit PCM is about 10.6 MB before container overhead. If you need MP3 afterward, use the audio format converter. The Web Audio specification describes offline rendering used for this operation.
Practical checks before sharing
Preview the full output, not only the first join. Check that your transitions do not mask words, that quiet recordings are still audible and that stereo placement stays sensible. The export safety pass reduces peaks above the digital limit but does not master the material or make all sources equally loud. Use the loudness meter if consistent loudness matters. Files are decoded in your browser and are not sent to our server. Very long combined files can run out of memory, so split a large job into smaller parts if export fails.
When a joiner is the wrong tool
If you need to pick exact entry points, change the speed of one recording or line up beats, a straightforward join is too simple. The mashup tool is intended for those two-track transitions. If you need several files playing at the same time rather than one after another, you need a multitrack editor. This joiner does not mix simultaneous full-length tracks. It overlaps only the ends and beginnings when you select a crossfade. A gap is silence, not a fade. Check your source rights before combining material for public distribution. A technically successful export does not grant permission to reuse someone else's recording.
Consider naming your files before adding them. Descriptive filenames make reordering easier when ten takes have nearly identical lengths. Keep the originals: the WAV export is a new file and does not modify any source. If the browser tab is refreshed, the decoded clips are lost and you will need to add them again. The tool does not keep a server-side project. Save the downloaded result before closing the tab, and test the result in a separate player if the finished recording is for a client or a live playback rig.