Online Bass Tuner
Tune four-string and five-string bass in standard, drop D or BEADG. Low-frequency microphone detection plus open-string reference tones.
--
Press Start to begin tuning
Works best in a quiet environment. Use headphones if playing back audio to avoid feedback.
Online bass tuner: four-string, drop D and five-string open notes
A standard four-string bass is E1, A1, D2 and G2 from the thickest string upward. A five-string bass normally adds a B0 below E1, while four-string drop D lowers only E1 to D1. Those low fundamentals make bass tuning different from checking a guitar through the same microphone. Choose your number of strings and tuning above, pluck one open string, then give the display a moment to stabilize. If your speaker cannot play a low reference tone clearly, use headphones or the microphone reading rather than turning the volume up.
Pick the correct bass preset
Four-string standard uses EADG. The drop D option uses DADG, with the other three strings unchanged. Five-string standard uses BEADG. The first note in each preset is the thickest string. The tool filters microphone readings to the neighborhood of those open pitches. Switching presets resets the displayed reading so a note from your previous tuning is not treated as a new result. If you tune to a different pattern or play a six-string bass, the chromatic tuner is a better match because it is not limited to these three open-string sets.
Low notes and what you hear
At A4 = 440 Hz, E1 is about 41.20 Hz, D1 is about 36.71 Hz and B0 is about 30.87 Hz. A small speaker may barely reproduce B0 at all. The upper harmonics of the bass note can be much louder than its fundamental, especially with a bright pickup or new strings. This can fool pitch detection into showing a note one octave too high. The bass preset uses a longer sample window to see more cycles of the lowest notes, but even that cannot correct a poor microphone signal. Fender's bass tuning guide discusses tuning by ear, with an app or with a dedicated tuner.
Use the reference buttons by ear
Each button plays its open-string target for up to 8 seconds. The notes follow your selected bass preset and A4 calibration. They use the same low-volume sine oscillator as the tone generator, so a laptop speaker may underrepresent the bottom end. Play your bass string, then listen to the reference on a playback device that can reproduce it. You can stop a tone by tapping the same button or start another string's tone. Use headphones if the microphone is listening at the same time. Otherwise the tuner might measure the speaker instead of your bass.
How the displayed cents are calculated
The closest open note in the selected preset is the target. The tuner calculates the logarithmic ratio of detected frequency to target frequency and multiplies it by 1,200 to show cents. A D1 at roughly 36.71 Hz is the drop D target. If your D1 is 37 Hz, the reading is around 14 cents sharp, depending on calibration and how stable the note is. A positive sign means sharp; a negative sign means flat. Within 5 cents is shown as in tune. The frequency calculator can help compare equal-tempered note frequencies outside this preset list.
Keep low-frequency readings steady
Pluck a single string and let the attack pass. Avoid playing two notes at once. Point your microphone at the cabinet or instrument, and reduce other sounds in the room. If using an electric bass unplugged, the microphone might hear too little signal for a steady pitch. A direct-input hardware tuner is more dependable on a noisy stage. Do not interpret a jump between B0 and B1 as proof the string jumped an octave. Try another pickup setting or pluck nearer the neck. Fender's tuning advice recommends checking after a pluck settles and limiting nearby noise.
Switching between standard and drop D
Lowering E1 to D1 is a whole step, or two semitones. Your lowest string now sits a fifth below A1, instead of a fourth. An ordinary EADG tab will not automatically make sense if you assume the low string is still E. If you use drop D for one song in a show, add a note to the setlist builder so you have time to retune. Check the rest of the strings again afterward; tension changes can shift their pitch. If the low string feels too loose, ask a technician about suitable string gauge and setup rather than increasing tension beyond what your instrument can handle.
What this tool cannot measure
Microphone permission is used for a live pitch estimate, not recording. Audio is processed locally. The instrument filter looks near open strings, not every fret on the neck. It cannot measure string action, intonation, pickup wiring or room acoustics. If the printed number stays fixed after you stop playing, stop and restart listening or try a quieter room. For live work, a clip-on or cable-connected tuner is easier to trust when multiple musicians are playing. Use the online tuner as a convenient practice check and verify difficult low notes with another reference when necessary.