Headphone & Speaker Test
Check playback channels, bass and polarity with short test tones. Keep your volume low.
Turn your volume down first. This is a playback check, not a measurement of your hardware or hearing.
Out of phase sends opposite polarity to left and right. On speakers it may sound quieter near the center; on headphones it may sound spatially unusual. Room acoustics and playback processing affect the result.
No test playing
Headphone and speaker test: check channels and bass playback
If the left test tone plays on the right side, something in your playback chain may be reversed. The buttons above send short tones to one channel at a time, both channels together, or both in opposite polarity. Start with the volume low. Check the left and right tests first, then try the bass sounds. The outcome is a listening observation, not a calibrated statement about frequency response, channel balance or hearing health.
Left and right channel checks
Each channel test plays a 440 Hz tone for 3 seconds. The browser uses a stereo panner at the far left or far right. On headphones you should hear the named side; on speakers you should hear the corresponding box. If both buttons sound centered, look for a mono accessibility setting, a single-channel audio cable or Bluetooth processing before blaming the file. Some speaker systems sum their input to mono deliberately. Try another device to narrow down the cause. The stereo width meter analyzes stereo recordings, which is a separate test from checking physical playback channels.
Bass tone and bass sweep
The 60 Hz button plays a low sine tone; the sweep moves from 40 to 200 Hz in 3 seconds. Thin speakers may barely reproduce the bottom of that sweep, and some headphones have their own bass boost. If a tone seems absent, do not turn the volume up sharply. Try a familiar music reference at your normal listening level. Room resonances can exaggerate particular frequencies, so a louder note during the sweep does not by itself prove a defect. Use the tone generator to repeat a specific frequency at a safe, steady level.
What out of phase means
Out of phase sends one waveform to the left output and its inverted copy to the right output. At the center between two speakers, those waves can partly cancel in the air. On headphones they are physically separated, so you will not hear the same acoustic cancellation. A mono switch or spatial processing may also change the result. This button is a demonstration of polarity, not a way to confirm every part of a speaker installation. Use caution if your device has loudness normalization or other audio effects enabled.
What the browser actually controls
The Web Audio API creates a sine oscillator and sends its signal through gain and channel routing nodes. The test is kept deliberately short and quiet. The MDN StereoPannerNode reference explains left-right panning in the browser. The signal then passes through your operating system, audio interface, amplifier and transducers. Any of those stages can change what you hear. The page does not measure sound pressure level at your ear or ask for microphone permission.
A sensible troubleshooting sequence
First confirm the headphones are on the correct ears or the speakers are in the intended positions. Then check left, right and center at the same low volume. If one channel is silent, inspect the connector and try another browser or playback device. Check operating-system balance and mono settings. If the tests pass but a song still sounds wrong, examine the recording itself with the spectrum analyzer or the stereo width tool. Avoid interpreting one failed test as proof of hearing loss.
Protect your ears
Tones are easy to replay and tempting to turn up. Keep playback comfortable, stop if you notice discomfort and take breaks during repeated checks. The US National Institute on Deafness and Other Communication Disorders explains why exposure level and duration both matter. Your device volume slider is not a sound-pressure meter. If you have persistent ringing, sudden hearing changes or concern about one ear, get advice from a qualified professional instead of relying on this page.
What a passing test does not prove
Hearing left and right at 440 Hz does not mean your headphones reproduce every part of a song accurately. Low bass can be missing, the two sides can have different levels at other frequencies, or a connector can fail intermittently. Conversely, if one button seems wrong once, browser routing might be at fault. Repeat at a comfortable level and compare with another known device. A proper speaker measurement uses a calibrated microphone and controlled test conditions. This page does not record the result, examine your operating system or automatically discover your device model.
For speakers, listening position changes the interpretation. Two speakers may cancel an inverted tone at one location and sound less affected elsewhere. For headphones, opposite polarity has no shared air path between ears, so the cancellation example cannot work the same way. If you are wiring passive speakers, follow your equipment manufacturer's instructions rather than using this single tone as a wiring diagram. The point of the polarity button is to demonstrate an audible difference under some conditions, not certify that an installation is correct.